Description
The GUTOR 0P0530-A076 is a communication interface PCB used in GUTOR UPS and inverter systems. The board is identified with reference 640-0673, and available listings specify Rev.01.
GUTOR documentation identifies the A076 position as the Communication Interface. The interface provides two serial RS232 outputs and is installed in the low-voltage section of the applicable UPS system.
The GUTOR system documentation also lists 0P0530 as a “PCB Assembly COM Interface for GUTOR and AIS,” confirming its role as a communications interface board rather than a power-supply or general-purpose I/O card.
📋 Product Datasheet
| Parameter | Specification |
|---|---|
| Brand | GUTOR Electronics |
| Model | 0P0530-A076 |
| Series | GUTOR UPS / Inverter Systems |
| Product Name | Communication Interface Board |
| Part Number | 640-0673 |
| Revision | Rev.01 |
| Product Type | PCB Communication Interface |
| Interface | 2 × Serial RS232 |
| System Position | A076 |
| Application | GUTOR UPS / Inverter Communication |
The two-RS232 configuration and A076 system position are documented by GUTOR system documentation.
⚠️ Exact board dimensions, weight, supply voltage, connector pinout, baud-rate configuration, and detailed electrical specifications should be verified from the actual PCB and the corresponding GUTOR system manual. Public references do not provide enough reliable information to state these values accurately.
🔧 Operating Standards & How to Use
🔹 Confirm the complete identification: 0P0530-A076 / 640-0673 / Rev.01.
🔹 Verify that the host equipment supports the A076 communication-interface position.
🔹 Install the board in the correct low-voltage section.
🔹 Check all communication connectors before energizing.
🔹 Use ESD protection when handling the PCB.
🔹 Verify RS232 wiring and connector assignments.
🔹 Do not connect RS232 ports to RS485 or Ethernet equipment without the appropriate interface converter.
🔹 Check communication parameters in the connected GUTOR system before commissioning.
The GUTOR system architecture places the A076 communication interface alongside the controller, signal controller, front panel, relay boards, and other low-voltage options.
▶️ Startup Sequence
- 🔍 Verify the board model, part number, and revision.
- 🧰 Inspect the PCB and connectors.
- 🔌 Check the RS232 cable connections.
- 🛡️ Verify grounding and cabinet safety.
- ⚡ Restore UPS control power according to the normal system procedure.
- 💡 Check system status indications.
- 🖥️ Verify communication between the UPS controller and connected equipment.
- 🔄 Check both serial communication ports where applicable.
- 📊 Confirm that monitoring data is being received correctly.
- 🧪 Perform a complete communication and UPS functional test.
⏹️ Shutdown Sequence
- Place the UPS/inverter into the approved maintenance or bypass state.
- Stop connected communication or monitoring equipment.
- Isolate the relevant control power.
- Apply lockout/tagout procedures when required.
- Verify that the board is electrically safe to handle.
- Disconnect the communication cables.
- Remove the PCB using ESD precautions.
- Install the replacement and reconnect the cables.
- Restore system power and perform a communication test.
⚠️ Do not remove the communication board while the system is energized unless the specific GUTOR equipment documentation explicitly permits live replacement.
📘 Product Usage Instructions
The 0P0530-A076 operates as an interface between the GUTOR UPS/inverter controller and external serial communication equipment.
A simplified arrangement is:
GUTOR UPS Controller → 0P0530-A076 Communication Interface → RS232 → External Monitoring / Communication Equipment
GUTOR documentation identifies A076 as a communication interface containing two serial RS232 outputs.
In GUTOR network-monitoring architectures, the communication interface can work with other communication hardware such as the Smart Slot Translator and Network Management Card. The documentation describes the communication path from the UPS controller through the A076 interface toward external monitoring equipment.
For replacement, record the original connector locations and cable assignments before removing the existing board. After installation, verify that the connected monitoring equipment receives the expected UPS status and event information.
🛠️ Installation & Maintenance
🔹 Keep the PCB dry and free from conductive dust.
🔹 Store it in an antistatic bag when not installed.
🔹 Avoid touching connector contacts.
🔹 Inspect RS232 connectors for bent or damaged pins.
🔹 Check communication cables for broken shielding or damaged insulation.
🔹 Inspect the PCB for corrosion or overheated components.
🔹 Verify connector seating after installation.
🔹 Record the PCB revision during replacement.
🔹 Confirm communication operation after maintenance.
❓ Common Questions & Answers
Q: What is GUTOR 0P0530-A076?
A: It is a GUTOR communication-interface PCB used in UPS and inverter systems.
Q: What is the part number?
A: The supplied board is identified as 640-0673, with available listings specifying Rev.01.
Q: What does A076 mean?
A: In GUTOR system documentation, A076 is the designated position for the Communication Interface option.
Q: How many communication ports does it have?
A: The GUTOR documentation identifies the A076 interface as having two serial RS232 outputs.
Q: Is 0P0530-A076 a power-supply board?
A: No. It is a communication interface board.
Q: Is it a PLC I/O module?
A: No. Its documented function is serial communication/interface rather than conventional digital or analog I/O.
Q: Can it communicate through Ethernet directly?
A: The A076 board itself is documented with RS232 outputs. Ethernet/network access in GUTOR monitoring systems can involve additional network-management hardware.
Q: Is 640-0673 the same board as 0P0530-A076?
A: The available industrial listing identifies 0P0530-A076 together with 640-0673 Rev.01, so these references are associated with the same board.
Q: Can another GUTOR communication board replace it?
A: Not automatically. Connector configuration, communication protocol, firmware, system position, and UPS compatibility should all be checked.
Q: Can the board be hot-swapped?
A: Do not assume hot-swapping is supported. Power should normally be isolated before PCB replacement unless the applicable GUTOR documentation explicitly permits live replacement.
Q: What should I check before purchasing?
A: Confirm GUTOR 0P0530-A076, 640-0673, Rev.01, PCB condition, connector arrangement, and compatibility with the customer’s GUTOR UPS/inverter.
⭐ Recommended GUTOR Related Series & Models
- GUTOR 0P0530-A076 — Communication Interface Board
- GUTOR 0P0530 — PCB Assembly Communication Interface
- GUTOR 0P0363 — Signalis Controller
- GUTOR 0M-94035A — Front Panel Complete
- GUTOR 0G-0399924A — Modbus Protocol Converter
- GUTOR 0P2420 — Network Management Card
- GUTOR 0P9912A — 16-Relay Board
- GUTOR 0P2439A — Masterlogic II PCB Assembly
- GUTOR 0P0280 — AC Supply PCB
- GUTOR 0P0284 — 220 VDC PSU
These are related GUTOR UPS/inverter system components and communication accessories, not confirmed direct replacements for 0P0530-A076. GUTOR documentation specifically distinguishes the A076 communication interface from the A074 protocol converter, A077/A078 relay boards, and A092 network-management card.
