Description
The Honeywell 900P01-0101 (P01 Power Supply) is a high-reliability AC-to-DC power conversion module engineered specifically for the Honeywell ControlEdge HC900 process and safety controller platform. It delivers regulated 5 VDC and 24 VDC distribution rails to satisfy the power requirements of controller racks, scanners, local I/O modules, and associated remote architecture. Housed in a compact, rugged industrial module format, it features universal AC input compatibility and built-in diagnostic test jacks.
📊 Product Datasheet Parameters
- 🏷️ Product Type & Model: P01 Power Supply Module (Model: 900P01-0101)
- ⚙️ Platform Compatibility: Honeywell ControlEdge HC900 Process Controller Series
- ⚡ Operating Voltage: 90 to 264 V AC, 47 to 63 Hz (Universal AC input)
- 🔌 Input Power Rating: 130 VA
- 🔋 Total Output Power Rating: 60 W continuous output capacity
- ⚡ Output Voltage Rails: Regulated +5 VDC and +24 VDC outputs
- 🔄 Inrush Current: 7 A peak-to-peak for 150 ms at 240 V AC
- ⏱️ Hold-Up Time: 20 ms at 115 V AC, 60 Hz (maximum load)
- 🔌 Wiring Terminations: Screw-type terminals supporting wire gauges #12–22 AWG
- 🛡️ Protection & Fusing: Internal, non-replaceable input fuse
- 🎛️ Diagnostic Features: Integrated 5 VDC and 24 VDC front test jacks behind a tool-secured access door
- 🌡️ Operating Temperature Range: Standard industrial environmental threshold (-20°C to +60°C)
📖 Product Instructions for Use
- Power Isolation: Ensure that all primary AC supply lines are completely shut off and locked out before installing, wiring, or extracting the 900P01-0101 module. This module is not hot-swappable.
- Mechanical Installation: Securely slide and lock the power supply module into the designated power supply slot on the left side of the HC900 rack backplane. Keep the tool-secured front door closed during normal operation.
- Wiring Connections: Connect line voltage, neutral, and earth ground securely to the screw terminals, ensuring proper torque and conductor retention within the #12–22 AWG specification range. Route high-voltage AC cables away from low-voltage signal loops.
- Voltage Verification: Utilize the built-in diagnostic test jacks located behind the front protective cover to measure rail voltages during initial commissioning or system troubleshooting.
❓ Common Questions & Answers (Q&A)
- Q: Can the 900P01-0101 power supply be hot-swapped while the rack is energized?
A: No. The unit lacks hot-swap circuitry; power must be completely isolated from the HC900 rack prior to removing or inserting the module.
- Q: What is the primary function of the front test jacks?
A: They serve strictly as internal monitoring points to check the 5 VDC and 24 VDC output levels using a multimeter. They must not be utilized as external auxiliary power taps for field devices.
- Q: How does the 60 W output handle large I/O complements?
A: The 60 W capacity supports standard mixed I/O configurations within a single rack, though larger high-density configurations should reference Honeywell’s power budget calculations to ensure limits are respected.
🏆 Recommended Honeywell Series & Models
- Honeywell 900P24-0101 P24 DC-Powered Supply Module
- Honeywell ControlEdge HC900 Controller (e.g., 900C30 / 900C50)
- Honeywell HC900 4, 8, and 12-Slot I/O Racks
- Honeywell Experion C300 Controller Module
- Honeywell CC-PDIL01 Series C Digital Input Module
- Honeywell CC-PDOB01 Series C Digital Output Module
- Honeywell CC-PAIH01 HART Analog Input Module
- Honeywell TK-FTEB01 Fault Tolerant Ethernet Bridge
- Honeywell Safety Manager Enhanced Controller
- Honeywell 900R08R-0300 Redundant Power Support Rack
