Description
🔧 Product Overview
The Schneider Electric PacDrive MC-4/11/10/400 is a high-performance servo drive from the legacy ELAU PacDrive MC-4 motion control platform.
This specific unit is identified with SW:00.22.XX, which is an important detail for replacement applications. It should not be treated as identical to an MC-4/11/10/400 carrying SW:00.16.32 simply because the main model number is the same. The PacDrive documentation specifically states that replacement units should have identical hardware and software configurations.
The MC-4/11/10/400 designation identifies the 10 A, 400 V version of the MC-4 family. The published MC-4 documentation lists the corresponding article number as 13130247.
⚙️ Key Features
- Schneider Electric / ELAU PacDrive MC-4 series
- Model MC-4/11/10/400
- 10 A rated current class
- 400 V three-phase supply class
- Software version SW:00.22.XX
- Integrated servo drive architecture
- Designed for PacDrive motion-control systems
- High-resolution encoder support within the MC-4 platform
- Electronic motor nameplate functionality
- Integrated braking/bleeder circuit
- Industrial cabinet mounting
- Suitable for multi-axis machine automation
- Exact hardware and software revision should be matched during replacement
📋 Product Datasheet
| Parameter | Specification |
|---|---|
| Brand | Schneider Electric / ELAU |
| Model | MC-4/11/10/400 |
| Series | PacDrive MC-4 |
| Product Type | Servo Drive |
| Article Number | 13130247 |
| Rated Current | 10 A |
| Rated Voltage Class | 400 V |
| Mains Supply | 3-phase AC |
| Mains Frequency | 48–62 Hz |
| Control Voltage | 24 VDC |
| DC Bus Voltage | Approx. 530–680 VDC |
| Motor Connection | Servo Motor Output |
| Software Version | SW:00.22.XX |
| Application | Motion Control / Servo Systems |
| Encoder | High-resolution encoder support |
| Mounting | Industrial Control Cabinet |
| Protection / Cooling | System-dependent; verify nameplate |
| Country of Manufacture | Germany reported for MC-4 platform |
| Condition | Verify actual item condition |
The MC-4 manual identifies the MC-4/11/10/400 as the 10 A, 400 V variant and gives article number 13130247. It also specifies a 3-phase/1-phase 380–480 V supply range for the MC-4 family, with 24 VDC control power and a 530–680 VDC DC circuit.
🔄 Operating Function
The MC-4 is a servo amplifier within the PacDrive motion-control architecture. It receives motion commands from the PacDrive control system and converts electrical power into controlled motor output.
A typical arrangement is:
PacDrive Controller → MC-4 Servo Drive → Servo Motor → Mechanical Axis
The drive manages motor current, speed, and positioning functions according to the commands and configuration provided by the motion-control system.
The MC-4 platform also supports electronic motor identification and high-resolution encoder feedback, allowing the drive and controller to work with the associated servo motor as a coordinated motion axis.
🛠️ Installation & Configuration
The software revision is especially important for this particular unit.
Before replacing an existing MC-4, check:
- Confirm the complete model: MC-4/11/10/400.
- Verify the article number where applicable: 13130247.
- Confirm the hardware revision from the nameplate.
- Confirm SW:00.22.XX.
- Compare the replacement software version with the machine’s original configuration.
- Verify the PacDrive controller and motion-system configuration.
- Check the servo motor model and encoder type.
- Confirm the 400 V three-phase supply.
- Verify the 24 VDC control supply.
- Inspect motor and encoder cables.
- Check grounding and cabinet connections.
- Back up the existing configuration before replacement.
- Perform a controlled axis test after installation.
The MC-4 service documentation explicitly warns that accurate system operation after component replacement requires identical hardware and software configurations.
⚠️ Important Software-Version Note
SW:00.22.XX is not simply a cosmetic variation of SW:00.16.32.
The two versions have been encountered on the same basic MC-4/11/10/400 model, but field replacement records show that a controller can report a firmware mismatch when the installed drive software does not correspond to the machine’s expected version. Therefore, the software revision should be checked before purchasing a replacement.
🔍 Maintenance Tips
- Keep the drive cabinet clean and dry.
- Maintain adequate cabinet ventilation.
- Inspect cooling paths for dust accumulation.
- Check power terminals for signs of overheating.
- Inspect motor and encoder cables.
- Monitor drive diagnostic codes.
- Record the hardware and software versions of installed drives.
- Keep a backup of the PacDrive configuration.
- Do not replace a drive solely by matching the front label.
- For a spare unit, record the exact SW and HW versions before storage.
If a replacement drive produces a configuration or firmware mismatch, verify the machine’s expected software version before attempting further commissioning.
❓ Frequently Asked Questions
Q: What is the MC-4/11/10/400?
A: It is a 10 A, 400 V class servo drive in the ELAU/Schneider PacDrive MC-4 family.
Q: What does the “10/400” designation mean?
A: In the MC-4 type designation, the 10 identifies the 10 A rated-current version and 400 identifies the 400 V version.
Q: What software version does this particular unit have?
A: The supplied product identification specifies SW:00.22.XX.
Q: Is SW:00.22.XX interchangeable with SW:00.16.32?
A: It should not be assumed to be interchangeable. The MC-4 documentation recommends identical hardware and software configurations for replacement.
Q: What is the article number associated with MC-4/11/10/400?
A: The MC-4 manual identifies article number 13130247 for this model.
Q: What input voltage does the MC-4 use?
A: The MC-4 family documentation specifies a 3-phase/1-phase 380–480 VAC supply range for the 400 V versions, with a 24 VDC control supply.
Q: Is this a PLC?
A: No. It is a servo drive used within the PacDrive motion-control system.
Q: What should I check when replacing an MC-4?
A: Check the complete model, article number, hardware revision, software version, motor, encoder, controller configuration, and machine application.
🔄 Recommended Schneider / ELAU PacDrive Models
- Schneider / ELAU MC-4/11/10/400 – 10 A Servo Drive
- Schneider / ELAU MC-4/11/03/400 – 3 A Servo Drive
- Schneider / ELAU MC-4/11/01/400 – 1.5 A Servo Drive
- Schneider / ELAU MC-4/11/05/230 – 5 A Servo Drive
- Schneider / ELAU MC-4/11/22/400 – 22 A Servo Drive
- Schneider / ELAU MC-4/11/50/400 – 50 A Servo Drive
- Schneider / ELAU PacDrive Controller – Motion Controller
- Schneider / ELAU PacDrive Servo Motor – Compatible Motion Motor
- Schneider / ELAU PacDrive Encoder Components – Motor Feedback
- Schneider / ELAU PacDrive EPAS-4 – Engineering and Diagnostic Environment
The MC-4 documentation lists several current and voltage variants, including 1.5 A, 3 A, 5 A, 10 A, 22 A, and 50 A versions. These are different drive configurations and should not be substituted without checking the machine’s electrical and motion requirements.
🏭 Application Summary
The Schneider Electric / ELAU PacDrive MC-4/11/10/400 is a legacy 10 A, 400 V servo drive designed for multi-axis industrial motion-control systems.
For this particular unit, SW:00.22.XX is a critical identification feature. When sourcing a replacement, matching only “MC-4/11/10/400” is not sufficient. The hardware revision, software version, motor configuration, encoder feedback, and PacDrive controller configuration should all be checked.
The MC-4 remains relevant as a maintenance spare for existing PacDrive machinery where replacing the complete motion-control architecture would be impractical.
