ABB AO810 | 3BSE008522R1 | Analog Output Module | S800 I/O 8 Channel

⚙️ Product Introduction

The ABB AO810, part number 3BSE008522R1, is an analog output module from the ABB S800 I/O system. It provides eight independent analog output channels for process-control applications.

The module is designed for connection to actuators, control valves, drives, and other field devices that require continuous analog control signals. It is commonly used with ABB automation platforms including System 800xA and AC 800M controller systems.

🔧 Analog Output Function

The AO810 converts digital control values from the ABB controller into analog output signals for field equipment. Each channel can be configured for current or voltage output depending on the application requirements.

The module includes channel-level diagnostics and supports reliable signal transmission for industrial process automation environments.

🏭 Typical Applications

• ABB System 800xA automation systems
• ABB AC 800M controllers
• Process industries
• Chemical plants
• Power generation
• Oil and gas applications
• Water treatment systems
• Industrial control valve operation
• Variable speed drive references

📋 Product Datasheet

Parameter	Specification
Manufacturer	ABB
Model	AO810
Part Number	3BSE008522R1
Product Type	Analog Output Module
I/O System	ABB S800 I/O
Number of Channels	8 Analog Outputs
Output Type	Current / Voltage Output
Current Output Range	4–20 mA
Voltage Output Range	0–10 V
Resolution	12 bit
Output Accuracy	±0.1% typical*
Isolation	Channel / System Isolation*
Power Supply	24 VDC
Current Consumption	Approx. 120 mA
Communication	S800 I/O Bus
Installation	S800 I/O Station
Mounting	DIN Rail
Operating Temperature	-25°C to +70°C
Dimensions	Approx. 102 × 119 × 45 mm
Weight	Approx. 0.25 kg
Country of Origin	Sweden

*Specifications may vary depending on configuration, firmware version, and system setup. Verify exact operating values before commissioning.

⚡ Key Features

• 8-channel analog output capability
• ABB S800 I/O compatible design
• Supports process-control output signals
• Suitable for valve and actuator control
• Channel diagnostics support
• Hot configuration capability in compatible systems
• Compact DIN rail mounting design
• Designed for continuous industrial operation

🔌 Communication & Integration

The AO810 communicates with ABB controllers through the S800 I/O communication architecture. It receives output commands from the controller and provides analog signals to connected field devices.

Typical configuration is performed through ABB engineering tools, where output channels, signal ranges, scaling values, and diagnostic parameters are assigned according to the process requirements.

🛠️ Installation Notes

Before installation, verify the complete identification AO810 / 3BSE008522R1, S800 I/O station configuration, terminal unit type, and field wiring requirements.

Install the module on the correct S800 I/O carrier and ensure the terminal connections are properly secured. Check power supply polarity and verify that connected field devices match the configured output type.

After startup, confirm module status LEDs, controller communication, output values, and connected actuator response.

⚙️ Commissioning Checklist

• Verify 24 VDC power supply
• Confirm S800 I/O bus communication
• Check module diagnostics
• Verify output channel configuration
• Confirm 4–20 mA or 0–10 V settings
• Check field device response
• Test output scaling
• Record operating parameters

⚠️ Compatibility Notice

The ABB AO810 3BSE008522R1 is an S800 I/O analog output module. It requires a compatible ABB I/O station, terminal unit, and controller configuration.

For replacement applications, confirm module revision, terminal unit compatibility, software configuration, and existing I/O mapping before installation.

📦 Product Identification

Brand: ABB
Model: AO810
Part Number: 3BSE008522R1
Product Type: Analog Output Module
I/O System: S800 I/O
Channels: 8 Analog Outputs
Signal: 4–20 mA / 0–10 V
Application: Process Automation