1. Product Description
The Bosch Rexroth IndraDyn S MSK071C-0450-NN-M1-UG1-NNNN (R911316155) is a synchronous servo motor designed for precision motion control in industrial automation systems. It is supplied in this listing with a LEM-RB-140T-21-NNNA radial cooling fan unit (R911394571), providing additional airflow for applications with frequent operating cycles or sustained motor operation. The MSK071C motor features a compact frame size, permanent-magnet synchronous technology, and an optical absolute encoder configuration. Its published motor data specifies 12 Nm continuous torque at standstill under a 60 K temperature rise, 14 Nm at 100 K, and 44 Nm maximum torque. The motor is suitable for compatible IndraDrive systems used in machine tools, packaging machinery, material handling, and automated production equipment. Before installation, verify the complete motor type code, encoder interface, holding-brake configuration, drive firmware, feedback cable, and cooling-fan electrical connection against the original machine documentation.

2. Key Technical Specifications
- Brand: Bosch Rexroth / Indramat
- Product Series: IndraDyn S MSK Synchronous Servo Motors
- Motor Model: MSK071C-0450-NN-M1-UG1-NNNN
- Motor Material Number: R911316155
- Motor Type: Permanent-magnet synchronous servo motor
- Frame Size: MSK071C
- Speed Code: 0450
- Continuous Standstill Torque (60 K): 12.0 Nm
- Continuous Standstill Torque (100 K): 14.0 Nm
- Continuous Standstill Current (60 K): 8.9 A RMS
- Continuous Standstill Current (100 K): 10.4 A RMS
- Maximum Torque: 44.0 Nm
- Maximum Current: 40.1 A RMS
- Maximum Speed: 5,800 rpm, according to published MSK071C-0450 data
- Protection Rating: IP65
- Cooling Arrangement: Natural motor cooling supplemented by the separately identified radial fan unit
- Encoder Configuration: M1 optical absolute encoder configuration; verify the exact interface and resolution from the motor nameplate and documentation
- Holding Brake: UG1 configuration; confirm the brake’s rated holding torque and electrical release requirements from the exact motor documentation
- Motor Weight: Approximately 13.9 kg for the published natural-convection motor configuration; verify the delivered assembly weight
- Operating Ambient Temperature: 0 to 40 °C under the published planning conditions
Cooling Fan Details:
- Brand: Bosch Rexroth
- Model: LEM-RB-140T-21-NNNA
- Material Number: R911394571
- Product Type: Radial motor cooling fan unit
- Rated Supply: 230 V AC, ±10%
- Frequency: 50/60 Hz
- Current: Approximately 0.20/0.18 A, based on the published LEM-RB-140T-21-NNNN family data
- Protection Rating: IP65
- Noise Level: Less than 75 dB(A), published family data
- Weight: Approximately 3.1–3.5 kg for the related LEM-RB-140T-21 family; exact NNNA variant weight not independently verified
The motor and fan specifications above are based on published MSK and LEM product-family data. Confirm exact suffix-specific ratings before selecting a drive or replacement assembly.
3. Application Scenarios
- CNC Machine Tools: Provides controlled servo motion for machine axes, positioning systems, and machining operations.
- Packaging Machinery: Supports synchronized motion in filling, sealing, labeling, and material-feeding equipment.
- Printing and Converting: Suitable for precision web handling, roller drives, and coordinated machine axes.
- Industrial Robotics: Can be integrated into compatible servo-driven positioning and handling mechanisms.
- Material Handling: Supports conveyor drives, transfer mechanisms, and automated positioning systems.
- Production Automation: Provides dynamic motor control for equipment requiring repeatable positioning and torque control.
- High-Duty-Cycle Applications: The supplied radial fan can provide additional cooling for applications with frequent operating cycles or sustained operation, subject to Rexroth’s permitted operating conditions.
4. Installation and Commissioning Procedure
- Record the motor nameplate information, complete type code, material number, serial number, and holding-brake designation.
- Confirm that the IndraDrive controller and power section support the MSK071C motor and its encoder configuration.
- Verify the motor power cable, encoder cable, brake wiring, and connector assignments against the Rexroth connection documentation.
- Check the LEM-RB-140T-21-NNNA fan nameplate and confirm its 230 V AC supply requirements.
- Isolate the drive and fan supply circuits. Apply lockout/tagout procedures and verify that the DC bus has discharged according to the manufacturer’s instructions.
- Inspect the motor shaft, mounting flange, connectors, fan housing, and cable entries for damage.
- Mount the motor using the approved flange arrangement and mechanical alignment procedure.
- Install the radial fan unit according to the Rexroth mounting instructions and confirm that airflow is unobstructed.
- Connect the motor, encoder, holding brake, and fan using the correct cables and wiring diagrams.
- Configure the motor identification and feedback parameters in the compatible IndraDrive system.
- Verify brake operation, encoder feedback, fan rotation, and motor temperature monitoring.
- Perform controlled commissioning at low speed before testing the complete operating range.
5. Configuration and Operating Guidelines
- Select the IndraDrive controller according to the motor’s current, torque, speed, and feedback requirements.
- Confirm that the motor identification data matches the complete MSK071C type code.
- Configure the encoder interface and feedback parameters according to the M1 option.
- Verify the holding-brake release voltage and control sequence for the UG1 configuration.
- Connect the radial fan to a suitable 230 V AC supply with correctly rated protection.
- Ensure that the fan operates whenever the application requires forced-air cooling.
- Keep the fan inlet and outlet clear of obstructions.
- Confirm the motor’s thermal limits and duty cycle using the applicable Rexroth motor data.
- Do not use the holding brake as a routine dynamic stopping device unless the application and manufacturer documentation explicitly permit it.
- Save the drive parameters and commissioning records before returning the machine to production.
6. Daily Maintenance
- Inspect the motor housing and mounting flange for damage, looseness, or abnormal vibration.
- Check the motor shaft and coupling for alignment and mechanical wear.
- Inspect the power and encoder cables for abrasion, bending damage, or loose connectors.
- Monitor motor temperature and drive diagnostic messages during operation.
- Check the holding-brake operation according to the manufacturer’s inspection procedure.
- Inspect the radial fan for dust accumulation, unusual noise, vibration, and reduced airflow.
- Clean the fan inlet and outlet without damaging the blades or enclosure.
- Verify that the fan receives the specified AC supply.
- Maintain records of motor operating hours, temperature trends, and maintenance activities.
- Back up drive parameters and motor configuration data before replacing components.
7. Troubleshooting and FAQ
Q1: The motor does not rotate after installation.
A: Check the drive enable status, power connections, motor identification parameters, encoder feedback, and safety interlocks. Review the IndraDrive diagnostic messages before replacing the motor.
Q2: The drive reports an encoder fault.
A: Inspect the encoder cable, connectors, shielding, and feedback interface configuration. Confirm that the controller supports the installed M1 encoder option.
Q3: The motor temperature rises during continuous operation.
A: Check the load, duty cycle, motor current, mounting conditions, and fan operation. Confirm that the application remains within the published thermal operating limits.
Q4: The radial fan does not operate.
A: Verify the fan nameplate, 230 V AC supply, protective device, wiring, and connector condition. Isolate the supply before inspecting the fan assembly.
Q5: The holding brake does not release.
A: Check the brake supply and control wiring, and verify the release sequence specified for the UG1 configuration. Do not force the shaft or apply an unverified voltage.
Q6: Can the motor operate without the supplied fan?
A: The motor’s permitted operating conditions depend on the load, duty cycle, mounting, and cooling configuration. Do not remove the fan from an application designed around forced-air cooling without checking the Rexroth motor planning documentation.
Q7: Can another MSK071C motor replace this model?
A: Not automatically. Verify the speed code, encoder option, holding brake, shaft design, electrical ratings, mounting dimensions, and drive parameters before substitution.
8. Safety Precautions
- Installation and commissioning must be performed by qualified servo-drive and electrical personnel.
- Isolate all motor, drive, and fan power circuits before servicing.
- Follow the manufacturer’s DC bus discharge procedure and verify safe voltage conditions.
- Secure the motor and driven mechanism before releasing or testing the holding brake.
- Never use the holding brake as an emergency stopping device unless the machine design and manufacturer documentation explicitly allow it.
- Keep hands, cables, and loose objects away from the fan blades during operation.
- Do not operate the fan with damaged wiring, exposed terminals, or a damaged housing.
- Maintain protective earth and correct cable shielding.
- Do not exceed the motor’s rated speed, current, torque, or thermal limits.
- Validate the complete drive system after motor replacement or parameter changes.
9. Related Bosch Rexroth Models and Accessories
The following are related IndraDyn S MSK motor models and cooling accessories for identification and sourcing reference. They are not automatically interchangeable with R911316155.
- MSK071C-0200-NN – Related MSK071C motor with a different speed code.
- MSK071C-0300-NN – Related MSK071C motor with a different speed code.
- MSK071C-0450-FN – Related MSK071C configuration with a different design suffix.
- MSK071C-0450-NN-M1-UG0-NNNN – Related encoder and brake configuration.
- MSK071C-0450-NN-M1-UG1-NNNN – Motor configuration corresponding to R911316155.
- MSK071C-0450-NN-M1-UG2-NNNN – Related holding-brake configuration.
- MSK071C-0450-NN-M1-UP0-NNNN – Related encoder and connection configuration.
- MSK071C-0450-NN-M1-UP1-NNNN – Related motor configuration.
- MSK071C-0450-NN-M1-UP2-NNNN – Related motor configuration.
- MSK071C-0450-NN-M2-UG0-RNNN – Related MSK071C encoder configuration.
- MSK071C-0450-NN-M2-UG1-RNNN – Related MSK071C motor configuration.
- LEM-AB-140T-21-NNNN – Axial cooling fan unit in the 140T family.
- LEM-RB-140T-21-NNNN – Related radial cooling fan unit.
- LEM-RB-140T-21-NNNA – Radial cooling fan unit, material number R911394571.
- LEM-AB-192T-21-NNNN – Related axial cooling fan family for other MSK motor sizes.
Always compare the complete motor type code, material number, encoder configuration, brake specification, and cooling accessory designation before ordering a replacement.
