Product Introduction
The SIGMATEK AKM54K-ANC2R-B0 is a permanent magnet synchronous servo motor from the AKM series, designed for dynamic industrial motion-control applications. Its brushless three-phase construction uses permanent magnets in the rotor to provide controlled torque, speed, and positioning when operated with a compatible servo drive. The AKM54K motor family is listed in SIGMATEK’s technical data with a rated torque of 10 Nm, peak torque of 38.4 Nm, rated speed of 3,500 RPM, and rated power of 3.68 kW under the documented 400 V drive supply condition. The seller advertises this particular item as 3.87 kW and 4,000 RPM, which differs from the published AKM54K family data and should be verified against the motor nameplate. The complete AKM54K-ANC2R-B0 designation must be retained when sourcing a replacement because feedback type, shaft execution, connector arrangement, and other options can affect drive compatibility.

Technical Parameters
- Brand: SIGMATEK
- Model: AKM54K-ANC2R-B0
- Product Series: AKM Servo Motor Series
- Motor Family: AKM54
- Motor Variant: AKM54K
- Product Name: Permanent Magnet Synchronous Servo Motor
- Product Type: Brushless three-phase AC servo motor
- Motor Technology: Permanent magnet synchronous
- Rated Power: 3.68 kW in the official AKM54K 400 V technical data; seller advertises 3.87 kW
- Rated Speed: 3,500 RPM in the official AKM54K technical data; seller advertises 4,000 RPM
- Rated Torque: 10 Nm
- Standstill Torque: 14.4 Nm
- Peak Torque: 38.4 Nm
- Standstill Current: 9.7 A
- Rated Current: 6.73 A
- Peak Current: 29.2 A
- Torque Constant: 1.50 Nm/A
- Rotor Inertia: 12 kg·cm²
- Motor Weight: 12 kg in the published AKM54K technical data; verify the complete suffix and accessories
- Rated Drive Supply: 400 V configuration indicated in the SIGMATEK AKM54K technical table
- Feedback: Exact feedback execution for ANC2R-B0 should be confirmed from the motor label and connector documentation
- Brake: Not confirmed for this exact suffix; verify before ordering
- Protection Rating: AKM series standard configuration is documented as IP65; optional shaft sealing can provide IP67 on applicable executions
- Cooling: Natural motor-surface heat dissipation; verify the applicable mounting and operating requirements
- Application: Industrial servo positioning and motion control
- Mounting: Flange-mounted motor; exact dimensions depend on the mechanical execution
- Place of Manufacture: Not independently confirmed for this individual unit
- Country of Origin: Seller references differ; verify the nameplate
- Dimensions: Confirm against the SIGMATEK AKM54 mechanical drawing and complete order code
- Product Status: AKM series lifecycle and availability should be confirmed with SIGMATEK
- Condition: Seller listing describes the item as new; confirm packaging, storage history, and nameplate condition
Key Technical Features
- Permanent magnet rotor: Provides high torque density and efficient synchronous motor operation.
- Brushless construction: Reduces routine maintenance associated with brushed motor designs.
- High dynamic response: Low rotor inertia supports frequent acceleration, deceleration, and direction changes.
- High peak torque: The published AKM54K family data lists a peak torque of 38.4 Nm.
- Three-phase winding: Designed for operation with a compatible servo inverter.
- Feedback-based motion control: Supports closed-loop speed and positioning control through the specified feedback system.
- Industrial protection: The AKM series standard configuration is documented with IP65 protection.
- Optional mechanical configurations: Shaft key, holding brake, shaft seal, rotatable connector, and different feedback systems are available across the AKM product family. The exact options on this motor must be confirmed.
- Multiple drive-voltage configurations: The AKM family includes variants designed for different rated supply conditions; the correct motor and drive combination must be selected.
Typical Applications
- CNC machine tools
- Packaging and filling equipment
- Printing and converting machinery
- Injection molding equipment
- Industrial robotics and handling systems
- Automated assembly lines
- High-speed positioning mechanisms
- Production machinery requiring dynamic servo control
Installation Procedure
- Verify the complete AKM54K-ANC2R-B0 model designation on the motor nameplate.
- Confirm the rated voltage, current, speed, torque, and feedback specifications.
- Compare the motor data with the selected SIGMATEK-compatible servo drive.
- Check the mounting flange, shaft diameter, shaft length, keyway, and coupling dimensions.
- Inspect the motor housing, shaft, connectors, and feedback assembly for damage.
- Confirm that the mounting surface is clean, flat, and mechanically suitable.
- Install the motor using the specified mounting hardware and tightening torque.
- Align the motor shaft with the driven mechanism and avoid excessive radial or axial loading.
- Connect the motor power cable according to the approved wiring diagram.
- Connect the feedback cable to the correct drive interface.
- Connect the temperature-monitoring circuit where provided.
- Verify protective grounding, shielding, cable routing, and connector locking.
- Check that the motor can rotate freely where the machine design permits.
- Complete the electrical and mechanical inspection before energizing the drive.
Startup and Power-On
⚠️ Initial commissioning must be performed by qualified personnel familiar with servo drives and industrial machine safety.
- Confirm that the motor is securely mounted and the driven mechanism is clear.
- Verify the incoming supply and servo drive ratings.
- Check the motor power and feedback connections.
- Confirm that the correct motor identification and feedback configuration are selected in the drive.
- Verify temperature-monitoring connections where applicable.
- Energize the drive system according to the machine manufacturer’s procedure.
- Check the drive status and diagnostic messages.
- Confirm that the feedback signal is valid.
- Enable the servo only after all safety interlocks are satisfied.
- Perform a low-speed test movement.
- Check rotation direction, motor current, vibration, and temperature.
- Increase speed and load gradually after successful initial testing.
Normal Operation
During normal operation, the servo drive supplies controlled three-phase current to the AKM54K motor. The permanent magnet rotor follows the rotating magnetic field generated by the stator, while the feedback system provides information required for closed-loop motion control.
The motor should operate within the specified speed, current, torque, and thermal limits. The published 38.4 Nm peak torque is a short-duration maximum rating, not a continuous operating torque. Operators should monitor drive alarms, motor temperature, vibration, current, and mechanical loading during production.
Parameter Configuration and Modification
- Use the SIGMATEK motor and drive documentation applicable to the installed hardware generation.
- Confirm the complete motor order code before selecting motor parameters.
- Verify the rated motor voltage, current, speed, torque, and power.
- Configure the feedback interface to match the actual installed feedback device.
- Confirm feedback direction and motor rotation direction before enabling full-speed operation.
- Set current, torque, speed, and thermal limits according to the motor and drive ratings.
- Configure acceleration and deceleration ramps according to the machine’s mechanical requirements.
- Check temperature-monitoring and fault-response settings.
- Configure holding-brake control only if the actual motor is equipped with a brake.
- Back up the original drive parameters before making changes.
- Do not transfer settings from another AKM54 motor without verifying its complete suffix and feedback configuration.
- Perform functional testing after any parameter modification.
Shutdown Procedure
- Stop the machine using its normal operating sequence.
- Bring the motor and driven mechanism to a safe position.
- Reduce the speed and torque commands to zero.
- Disable the servo drive through the machine controller.
- Switch off the relevant power supply according to the machine shutdown procedure.
- Apply lockout/tagout before maintenance.
- Wait for the servo drive DC bus to discharge according to the manufacturer’s instructions.
- Verify that hazardous voltage is absent before disconnecting cables.
- Protect motor connectors against moisture, dust, and mechanical damage during storage.
Daily Maintenance
- Inspect the motor housing for cracks, impact damage, and contamination.
- Check the shaft and coupling for abnormal wear or looseness.
- Inspect power and feedback cables for abrasion and damaged connectors.
- Monitor motor temperature during normal operation.
- Listen for unusual bearing noise.
- Check for excessive vibration or mechanical resonance.
- Keep the motor surface clean to support heat dissipation.
- Inspect mounting bolts and mechanical connections.
- Review servo drive alarms and fault history.
- Check the condition of the feedback and temperature-monitoring connections.
- Follow the manufacturer’s maintenance schedule for bearings, seals, and optional brake assemblies.
Troubleshooting
1. Motor does not start
- Check the servo drive power and ready status.
- Verify the drive-enable command and safety interlocks.
- Inspect motor power connections.
- Review active drive alarms.
- Confirm that the correct motor configuration is selected.
2. Feedback alarm
- Inspect the feedback cable and connectors.
- Verify that the drive interface matches the installed feedback device.
- Check shielding and cable routing.
- Review feedback configuration and diagnostic messages.
3. Motor overheats
- Check the mechanical load and duty cycle.
- Verify current and torque limits.
- Inspect the motor mounting and heat-dissipation conditions.
- Check for excessive acceleration or repeated overloads.
- Confirm that temperature monitoring is functioning.
4. Excessive vibration or noise
- Inspect shaft alignment and coupling condition.
- Check the driven mechanism for binding.
- Inspect motor mounting and bearing condition.
- Review servo tuning and operating speed.
- Check for mechanical resonance.
5. Motor cannot reach commanded speed
- Verify the drive’s speed and current limits.
- Check the mechanical load.
- Confirm the motor identification parameters.
- Inspect the power supply and drive status.
- Review any active overload or thermal limitations.
6. Unexpected motor movement
- Stop the machine immediately.
- Verify motor direction and feedback configuration.
- Check axis assignment and control parameters.
- Inspect the machine safety and interlock circuits.
- Restart only after the cause has been identified and corrected.
Frequently Asked Questions
Q1: What type of motor is the SIGMATEK AKM54K-ANC2R-B0?
It is a permanent magnet synchronous servo motor from the SIGMATEK AKM series.
Q2: What is the rated power of the AKM54K?
SIGMATEK’s published AKM54K technical data lists 3.68 kW for the 400 V configuration. The seller advertises 3.87 kW, so the actual unit’s nameplate should be checked.
Q3: What is its rated speed?
The official AKM54K family data lists 3,500 RPM. The seller title states 4,000 RPM. Confirm the exact rating from the motor label before selecting a replacement.
Q4: What are the rated and peak torque values?
The published AKM54K data lists 10 Nm rated torque and 38.4 Nm peak torque.
Q5: Does this motor have a holding brake?
The complete suffix should be checked to establish whether a brake is installed. Do not assume a brake is included based on the AKM54 family designation alone.
Q6: What feedback device does it use?
The precise feedback execution associated with ANC2R-B0 should be confirmed using the nameplate and connector documentation. Select a drive with a matching feedback interface.
Q7: Can it replace another SIGMATEK AKM54 motor?
Not automatically. Feedback, shaft, brake, connector, and electrical ratings may differ between variants. Compare the complete order codes and machine drawings before substitution.
Q8: Which servo drive can operate this motor?
Use a compatible servo drive that supports the motor’s voltage, current, feedback device, and required control functions. Confirm the exact drive pairing using SIGMATEK documentation.
Safety Precautions
⚠️ Electrical Safety: Isolate the servo drive supply and follow lockout/tagout procedures before installation or maintenance.
⚠️ Stored Energy: Allow the drive DC bus to discharge according to the manufacturer’s instructions and verify safe voltage before handling electrical connections.
⚠️ Permanent Magnet Safety: The motor can generate voltage when its shaft is rotated. Follow the manufacturer’s handling and service procedures.
⚠️ Mechanical Safety: Secure the driven mechanism before testing. Unexpected motor movement can cause injury or equipment damage.
⚠️ Feedback Protection: Do not connect or disconnect feedback cables while the system is energized unless the OEM procedure explicitly permits it.
⚠️ Replacement Compatibility: Verify the complete suffix, electrical ratings, feedback configuration, shaft dimensions, and brake arrangement before installing a substitute.
Related SIGMATEK AKM Models
The following are documented models from the same SIGMATEK AKM servo motor family. They are useful for product-family identification and comparison, but they are not automatic drop-in replacements.
- AKM53K
- AKM53M
- AKM53P
- AKM54G
- AKM54H
- AKM54K
- AKM54L
- AKM54N
- AKM62G
- AKM62K
- AKM62M
- AKM62P
- AKM63G
- AKM63K
- AKM63M
Replacement Note: When replacing the AKM54K-ANC2R-B0, compare the full motor code, rated power, speed, torque, feedback system, shaft execution, brake option, connector arrangement, and drive compatibility. The AKM54K base designation alone does not establish mechanical or electrical interchangeability.
